Amphibia Torture Test

Pengetest-an Suhu pada Jam Vostok Amphibia Automatic

  

                                Sebelum di Test                              Lalu di bekukan hingga -20 C

  

Kemudian di siram air panas hingga suhu +100 C

  

Di celupkan di dalam air panas bersuhu +100C

Setelah Pengetest-an Jam ini masih bekerja dengan OK!

Klik di sini untuk melihat film ketangguhan jam ini dalam Test Temperature sesungguhnya!

sumber : http://arloji.orangkomputer.com/?p=619

Catatan Servis Vostok Amphiba 2416b

Vostok 2416b Service notes

Service notes
Boctok caliber 2416b
By. Dave Murphy

Instructions are below each picture.

Back Side:

Remove 1 screw and rotor
Remove Stem
Remove movement from case
Remove hands and dial

Remove:
1 screw and reversing wheels keeper
3 screws and auto-wind bridge

Remove:
1.) Reversing Wheels
2.) First Reduction Wheel
3.) ratchet wheel driving wheel
4.)Screw, click, and click spring underneath
5.)screw and ratchet wheel
6.)Left Hand screw and crown wheel

At this point, You can (and should) unwind the mainspring barrel.

Remove 2 screws and Movement Spacer
Remove 2 Dial Screws (not seen in this photo)
Remove Calendar Jumper Spring
Remove 3 screws and Calendar cover plate

Note:
These are Flat head screws

Remove:
1.) Calendar Jumper
2.) Foil
3.)Hour Wheel
4.)Date Ring
5.)intermediate calendar wheel
6.)screw and Calendar wheel
7.)Calendar cam (under the calendar wheel)
8.)screw and Calendar cam spring (under the date ring)

Remove:
3 screws and Keyless Cover

Note:
These are Cheese head screws

Remove:
1.)minute wheel
2.)setting wheel
3.)setting yoke spring
4.)setting yoke
5.)setting lever
6.)sliding pinion
7.)winding pinion

Remove Cannon Pinion. I used the #1 Presto Hand puller

Remove:
shock spring
cap jewel
Pierced jewel

Remove Shock spring, cap, and pierced jewel on the other side

Note: use tool made from pegwood

Remove:
1.) 1 screw and wheel train bridge. Make note of the location of this screw.
2.) 3rd wheel
3.) 4th wheel (underneath)
4.) escape wheel (underneath)

Remove:
1.) Second reduction gear for auto-wind
2.) 1 screw, seconds hand pinion spring, and seconds hand pinion
3.) 3 screws and winding bridge

Remove:
1.) Center Wheel
2.) Winding barrel
3.)Crown wheel click post. Spring will be attached to winding bridge underside.
4.) Stem Release button
5.) 1 screw and balance assembly

Remove:
1.) 1 screw and pallet lever bridge
2.) pallet lever

Boctok 2416b
Cleaning and Oiling notes
Dave Murphy

Cleaned in ultrasonic cleaner, in 3 beakers.
Cleaning: 2 cycles in L&R Extra Fine Watch Cleaning Solution
First Rinse: 1 cycle in L&R Ultrasonic Watch Rinsing Solution
Final Rinse: 1 cycle in L&R Ultrasonic Watch Rinsing Solution

1 load: Entire keyless, setting, and calendar works EXCEPT day ring
1 Load: Motion works
1 load; all plates and bridges
1 load: Balance assembly, alone

After final rinse:
Balance assembly, balance pierced and cap jewels, shock assemblies rinsed in “One Dip” hairspring cleaner.

Oiling strategy:

Moebius 9010 on low-load jeweled pivots
Moebius 9020 on medium-load jeweled pivots
Moebius D-5 on high-load jeweled pivots
Moebius 9415 on pallet stones
Moebius 8141 in the mainspring barrel
Moebius 8217 Braking grease on the mainspring barrel wall
PML Stem Grease for metal-to-metal sliding contact

Oiling amounts:
Using the black oiler,
Light = dipped to a depth 1/3 of the oiler’s width.
Medium= dipped to a depth 2/3 of the oiler’s width.
Heavy= dipped to a depth equal to the oiler’s width.

Unless noted, use light to medium oiling on the black oiler.

Boctok 2416 Assembly and Oiling
Dave Murphy

Lubricate:
Mainspring Barrel Wall in 2 places, 8217, yellow oiler, medium heavy

Assemble:
Arbor to Mainspring using pin vise (inset)
Wind spring into barrel

Lubricate:
Barrel floor, 8141, yellow oiler medium-heavy
Mainspring coils, 8141, yellow oiler, medium heavy

Assemble:
Barrel cover

Lubricate:
Barrel arbor, D5, (both sides) (inset)

Assemble:
Pallet Lever
Pallet lever bridge and 1 screw

Do not Lubricate the Pallet lever pivots.

Identification of wheels

Lubricate:
Brass pin for crown wheel click post, PML
Area where crown wheel click post slides, PML

Assemble:
1.)Winding Bridge (this view is the underside)
2.) Crown Wheel Click post, so it pivots on the brass pin
3.) Crown wheel click post spring

Assemble:
Mainspring Barrel (inset)
Center Wheel (inset)
The Stem Release Button! (inset)

Winding bridge and 3 screws. The Crown wheel click post must pivot and spring back when it is assembled.

Lubricate:
Center wheel jewels, D-5, (both sides)
Barrel Arbors, D-5 heavy, both sides

Assemble:
1.) Escape wheel (inset)
2.) 4th wheel (inset)
3.) 3rd wheel (inset)
4.) Second winding reduction wheel
5.) Wheel train Bridge and 2 screws (inset)

Lubricate:
Escape wheel pivots 9010 both sides
4th wheel pivots 9010 both sides
3rd wheel pivots 9020 both sides
Second winding reduction wheel post, D-5

Assemble:
Seconds hand pinion

Lubricate:
bearing surface, underside of seconds hand pinion spring, D-5
surface under click, 9010

Assemble:
seconds hand pinion spring and 1 screw
ratchet wheel and 1 screw
click spring
click and 1 screw
crown wheel

Lubricate:
click post 9010
crown wheel post D-5

Assemble:
Left hand screw to crown wheel

Flip to the dial side of the movement.
Lubricate pallet stones, Light 9415, on impulse surfaces only. Access is through the 2 rectangular holes.

Assemble:
balance assembly, 1 screw

Lubricate cap jewel, medium heavy, to cover 1/2 to 2/3 of cap jewel (inset)

Assemble pierced jewel to cap jewel
assemble shock assemblies with pegwood tool.

At this point, movement should run. Put a screwdriver in the screw holding the ratchet wheel, and wind.

Assemble:
Ratchet wheel driving wheel (inset)
First winding Reduction Wheel (inset)
Auto-wind bridge and 3 screws
Both reversing wheels
Reversing wheels keeper and 1 screw

Lubricate:
Posts for Reversing wheels, D-5
1 jewel in each reversing wheel, D-5
First winding reduction wheel jewels, D-5, both sides
Ratchet wheel driving wheel jewels, D-5, both sides

Lubricate:
Stem pivot, PML
Stem clutch square, PML
Stem set lever notch, PML
Stem shoulder, PML

Assemble:
Stem
Sliding Clutch Pinion
Winding Pinion

Lubricate:
Sliding Clutch pinion slot, PML
Sliding Clutch pinion Breguet teeth, PML
Winding Pinion Breguet teeth, PML

Lubricate:
Seconds hand pinion, 9010
Center wheel post, D-5

Install Cannon pinion using pin vise

Lubricate with PML:
Stem Release button
Post for setting yoke
Post for minute wheel
Post for setting wheel

Assemble:
minute wheel
setting wheel
setting lever
setting yoke
setting yoke spring

Lubricate with PML:
“heel” of setting yoke
post on setting lever
side of setting lever where keyless cover springs against it
edge of setting lever where it touches the setting yoke

Assemble:
Keyless cover and 3 screws. (inset)
note: hook the cover spring on to the post on the setting lever

Lubricate outside of Cannon pinion, 9020

Lubricate with PML:
post for intermediate calendar wheel
under calendar cam
post for date ring jumper

assemble:
Hour Wheel
Dial Foil (not shown)
intermediate calendar wheel
calendar cam
date ring jumper

Lubricate with PML:
top of calendar wheel
hub+shoulder of calendar wheel screw

Install:
date wheel jumper
calendar wheel with 1 screw
calendar cam spring and 1 screw

Lubricate:
2 or 3 teeth of the date ring, PML

Assemble:
Date ring,
Calendar cover and 3 screws
calendar jumper spring

Assemble:
Dial screws
Movement spacer and 2 screws
Dial and hands
Rotor and 1 screw

Lubricate:
rotor bearing, 9020

By Dave Murphy; February 12th, 2010 at 17:34. Reason: re-linked pics

VROW.swf

sumber :  http://arloji.orangkomputer.com/?p=797

Petunjuk penggunaan Arloji Vostok Amphibia 2416B

Pada halaman ini Anda akan menemukan petunjuk tentang cara untuk mengatur Jam tangan Vostok Amphibia anda. Instruksi ini berlaku untuk jam tangan yang menggunakan Movement 2416B.

Jika Anda mengenakan arloji di tangan Anda setiap hari tidak perlu untuk memutar manual mekanik utk sumber tenaga gerakan jam. Jam tangan ini menggunakan sebuah gerakan yang otomatis sehingga jam tangan tetap berjalan oleh pergerakan tangan Anda. Tapi jika Anda tidak memakai jam tangan lebih dari 24 jam itu perlu untuk di putar kembali.

Cara untuk menjaga agar jam tangan tetap hidup tidak mati adalah dengan cara:

Putar knop jam berlawanan arah jarum jam dari kasing ini. Kemudian tarik sehingga knop berada di posisi 2. Mulai lah putar searah jarum jam dengan memutar knop sebanyak kira2 25-30 putaran. Dengan perasaan anda cobalah utk mengeluarkan sedikit knop sehingga tidak kembali ke posisi 1.

Jangan sampai berlebihan dalam memutar yang dapat menyebabkan mesin mekanik menjadi rusak.

Setelah selesai memutar kembalikan knop ke posisi 1 dan kencangkan.

Cara Terbaik untuk agar Arloji ini dapat berjalan terus mekanis nya adalah dengan menggunakan nya terus jam ini jangan sampai di lepas.

Mengatur Jam Menit, dan Tanggal.

Putar knop jam berlawanan arah jarum jam dari kasing ini. Kemudian tarik sehingga knop berada di posisi 3. Anda akan mendengar dan merasa klik. Putar knop dengan berlawanan arah jarum jam untuk mengatur jam, menit dan tanggal yang tepat. Setelah pengaturan waktu,kembalikan knop ke posisi 1.

Trik untuk mengubah tanggal.

Putar knop jam berlawanan arah jarum jam dari kasing ini. Kemudian tarik sehingga knop berada di posisi 3. Putar knop berlawanan arah jarum jam sampai satu jam tangan mencapai 12. Lalu mundur dan putar searah jarum jam sampai satu jam tangan mencapai 8. Reverse dan kembali ke 12. Ini akan memindahkan tanggal satu posisi. Ulangi seperlunya. Setelah selesai, kembalikan knop ke posisi 1.

CATATAN: Jangan pernah langsung dari posisi 3 (posisi waktu-pengaturan) ke untuk posisi 2. Sebaiknya kembalikan knop ke posisi 1 dahulu baru kemudian lanjutkan ke posisi 2. Jadi setelah pengaturan waktu atau tanggal, sekrup knop ditutup dulu di posisi 1 baru kemudian ke posisi 2 untuk memutar sebagai pensupply tenaga manual mekanik.

Perawatan Jam Tangan

Jangan Memasukan Jam tangan ke dalam air kecuali knop benar-benar disekrup kencang di posisi 1. Anda akan merasakan karet seal gasket bila disekrup sepenuhnya.

Untuk mencegah embun di bawah kaca jam tangan pastikan selalu Knop benar-benar sudah disekrup di posisi 1 dengan kencang.

Lindungi jam tangan dari guncangan, produk kimia, dan medan magnet.

Untuk mencegah penetrasi debu dan kotoran dalam mekanisme, jangan pernah buka penutup belakang kasing jam tangan ini.

sumber : http://arloji.orangkomputer.com/?p=460

Petunjuk menggunakan Arloji Vostok Automatic – 2416B Movement.

Pada halaman ini Anda akan menemukan petunjuk tentang cara untuk mengatur Jam tangan Vostok Amphibia atau Komandirskie Automatic anda. Instruksi ini berlaku untuk jam tangan yang menggunakan Movement 2416B.

Jika Anda mengenakan arloji di tangan Anda setiap hari tidak perlu untuk memutar manual mekanik (winding) utk sumber tenaga gerakan jam. Jam tangan ini menggunakan sebuah gerakan yang otomatis sehingga jam tangan tetap berjalan oleh pergerakan tangan Anda. Tapi jika Anda tidak memakai jam tangan lebih dari 24 jam itu perlu untuk di putar kembali.

Cara untuk menjaga agar jam tangan tetap hidup tidak mati adalah dengan cara:

Putar kron jam yang berada di samping kanan jam berlawanan arah jarum jam atau putar ke bawah dari kesing ini. Kemudian tarik sehingga kron berada di posisi 2. Dengan perasaan anda cobalah utk mengeluarkan sedikit knop sehingga tidak kembali ke posisi 1. Mulai lah putar searah jarum jam atau ke atas dengan memutar kron sebanyak kira2 25-30 putaran. Jangan sampai berlebihan dalam memutar yang dapat menyebabkan mesin mekanik menjadi rusak.

Setelah selesai memutar kembalikan kron ke posisi 1 dan kencangkan agar air tidak masuk.

Cara terbaik untuk agar Arloji ini dapat berjalan terus mekanis nya adalah dengan menggunakan nya terus jam ini jangan sampai di lepas.

Mengatur Jam Menit, dan Tanggal.

Putar kron yang berada di samping kanan jam berlawanan arah jarum jam dari kesing jam ini. Kemudian tarik sehingga kron berada di posisi 3. Anda akan mendengar dan merasa klik. Putar kron dengan berlawanan arah jarum jam untuk mengatur jam, menit dan tanggal yang tepat. Setelah pengaturan waktu,kembalikan kron ke posisi 1. jangan lupa untuk di kencangkan agar air tidak masuk.

Trik untuk mengubah tanggal.

Putar kron yang berada di samping kanan jam berlawanan arah jarum jam dari kesing jam ini. Kemudian tarik sehingga kron berada di posisi 3. Putar kron berlawanan arah jarum jam sampai jarum jam mencapai pukul 12 malam maka tanggal akan berubah. Lalu putar mundur dan jarum jam ke pukul 8 malam, kemudian putar kembali ke arah jam 12 malam kembali hingga tanggal berubah dan bertambah. Ulangi seperlunya 12-8-12. Setelah selesai, kembalikan kron ke posisi 1.

CATATAN: Jangan pernah lakukan langsung pemindahan kron dari posisi 3 (posisi waktu-pengaturan) ke untuk posisi 2. Sebaiknya kembalikan kron ke posisi 1 terlebih dahulu baru kemudian lanjutkan ke posisi 2. Jadi setelah pengaturan waktu atau tanggal, kron ditutup dulu di posisi 1 baru kemudian ke posisi 2 untuk memutar sebagai pensupply tenaga manual mekanik.

Perawatan Jam Tangan

Jangan Memasukan Jam tangan ke dalam air kecuali kron benar-benar di kencang kan pada posisi 1. Anda akan merasakan karet seal gasket bila disekrup sepenuhnya.

Untuk mencegah embun di bawah kaca jam tangan pastikan selalu Kron benar-benar sudah dikunci pada posisi 1 dengan kencang.

Lindungi jam tangan dari guncangan, produk kimia, dan medan magnet.

Untuk mencegah penetrasi debu dan kotoran dalam mekanisme, jangan pernah buka penutup belakang kasing jam tangan ini.

sumber : http://arloji.orangkomputer.com/?p=1225

Tabel Serial Mesin Arloji Vostok

Vostok menghasilkan semua gerakan mekanis dengan sendirinya. Perusahaan Vostok juga memiliki anak-perusahaan “Briolet” yang mengkhususkan diri pada produksi permata ruby-jewels. Vostok juga memasok mesin bagi pabrikan arloji lainnya seperti Vostok-Europe, Volmax, Moskow Classic dan Poljot-International. Semua gerakan mekanis berosilasi pada 19.800 per semi-alternations . Tidak termasuk pada presisi kronometer 2809 yang diproduksi untuk sementara waktu, gerakan kaliber 24mm dari Vostok disajikan dalam tabel di bawah ini:

sumber : http://arloji.orangkomputer.com/?p=435

Rangkaian mesin Vostok

Berikut Adalah Gambar Rangkaian dalam Mesin Vostok seri 2416B biasa di gunakan pada model Vostok Komandirskie, Amphibian,  Kremlyovskie,  Prestige, Breeze, Titanium,  2416B,  VIP,Vostok-Europe Pobeda.

sumber :  http://arloji.orangkomputer.com/?p=439

The anatomy of a Vostok

By:  marc_wl

Vostok watches are very particular. Komandirskie or Amphibia series, they share some very specific features that are sometine surprizing for the newbies. They are very rugged, inexpensive, with a design directly inherited from the late 60′s 

The screwing crown is for instance very surprizing . Who did not believe that the crown was broken at the first manipulation? Both Amphibia and Komansdirkie absolutely required to have their crown screwed down to be water resistant. Most of the time the other brands adopted a toric gasket on a slick tube and the screw down is just and additional protection. Why don’t we see this in details?

Our guinea pig today is the Komandirskie version of the “blue diver” (circa 2004 automatic caliber Vostok 2416b 32 jewels). Something wrong happened in the dato mecanism and I need the mesh bracelet to put it on my Amphibia version.

The main difference compared to Amphibia versions is the brass chrome-plated case instead of the all stainless steel, a ca 5atm resistance instead of 20atm, a thiner acrylic crystal, but the rest is quite similar. Straight hand and no lumed spot on the second hand.

The mesh bracelet waspurchased from my local watchmaker. It has a safely buckle.

Someone, a few time ago on this forum asked how to remove the rotating bezel. Its a good occasion to see how to proceed. First, protect the case with a piece of strong paper. Then lift off smoothly the bezel using a Bergeon-like knife.

It comes effortless and it can be snapped on back easily as well

The bezel is in brass and chrome-plated too. A bulged wire give the necessarily bezel friction :

Well. Now we can open the case. A case holder is required.

A good care is to put on a protective film on the case back to prevent any damage with opening tool that need to be adapted to the screwed ring size.

As soon as the ring is unbloked, one can continue using a safe wood pick to fully unscrew the compressing ring that can be removed :

Then we lift the case back using the small finger and remove it

Here is the movement and the Vostok rotor:

For the demo purpose I remove the gasket.

One can now extract the stem+crown. Be carefull, this screw is not the stem-liberating one but just a bridge screw!

There a specific pusher near the click that more handy that a screw

Here the stem tube with its outer thread.

And here is now the famous upsetting crown!

If the crown is not pulled out, it is fully free to move, but when you screw it down you don’t turn the stem anymore! Very clever! Now you can see the inner gasket and understand that it should be screwed down to protect the watch!!

We now remove the rotor to be more comfortable in the following steps

After putting the screw in a safe place, we can lift off the rotor

Well, we can now uncase the movement just by unscrewing the 2 casing screws on the nylon ring.

The movement is free. Be carefull not to dammage the dail and the hands attached.

We deposit it on another caliber holder to proceed to the hand lift :

We should first get a minimum alignment to lift them all at the same time. One protects the dial with paper and a sharp V:

We take the hour hand with the lifter an push gently to lift the whole

It’s Done!

That’s the Deep Blue !

We can now remove the dail. 2 small screws block the dial feet on the periphery

It comes effortless and the dato mechanism appears :

A wire spring in the small window should be carefully removed before unscrewing the plate.

So what’s going wrong in this dato??

Ha! OK. I see I broke 2 teeth (orange arrow) of the hour wheel (blue arrow). I remember that something went hard while changing the time and I forced a bit (never do this!).

So that the hour hand stopped at 1 am to 1 pm while the other continued their run!!

I’ve asked to Peter Maier if I could get a new one with my Ministry and Neptune order. Hope so.. While waiting, I keep the whole away from the dust.

What is more magnificient than any running caliber outside its case !

sumber :  http://arloji.orangkomputer.com/?p=884